Read and understand this manual and all instructions before operating the DR CHIPPER/SHREDDER. `Original Language DR® CHIPPER/SHREDDER SAFETY &
10 DR® CHIPPER/SHREDDER Figure 6 Frame Support 5/16" Bolt 5/16" Bolts Bent Hitch Plate Tow Beam 3. Remove the Tow Beam and lift th
CONTACT US AT www.DRpower.com 11 Attaching the Chipper Hopper Tool Needed: 1/2" Wrench Tip: Insert a towel or large rag into the open
12 DR® CHIPPER/SHREDDER Check the Tire Pressure Tools Needed: Tire Pressure Gauge Air Compressor or Hand Pump 1. Remove the Valve Stem Pr
CONTACT US AT www.DRpower.com 13 Read and understand the warnings listed in “Chapter 1 General Safety Rules” before operating this CHIPPER/SH
14 DR® CHIPPER/SHREDDER Read and understand the warnings listed in “Chapter 1 General Safety Rules” before operating this CHIPPER/SHREDDER. Th
CONTACT US AT www.DRpower.com 15 The Hammers within the Shredding Chamber can tug suddenly at material fed into the Shredder Hopper. Do not
16 DR® CHIPPER/SHREDDER To Free a Jammed Flywheel 1. Remove any material left in the Chipper/Shredder Hopper. 2. Check the Discharge Opening
CONTACT US AT www.DRpower.com 17 Chapter 4: Maintaining The DR CHIPPER/SHREDDER Regular maintenance is the way to ensure the best performance
18 DR® CHIPPER/SHREDDER Grease Fittings Your DR CHIPPER/SHREDDER was greased at the Factory. The operator needs to lubricate the Chipper Side
CONTACT US AT www.DRpower.com 19 7. While holding the Adjust Nut, retighten the Jam Nut. 8. Retighten the Engine Bolts. 9. Check the align
2 DR® CHIPPER/SHREDDER This indicates a hazardous situation, which, if not avoided, could result in death or serious injury. Table of Contents
20 DR® CHIPPER/SHREDDER Knife Sharpening You should never attempt to sharpen the Chipper Knife freehand; take the Knife to a machine shop fo
CONTACT US AT www.DRpower.com 21 5. While applying a counterclockwise force with the Allen Wrench, apply heat from a propane torch to the Sc
22 DR® CHIPPER/SHREDDER 4. To adjust the Wear Plate Gap, loosen the three 1/4" Nuts using a 7/16" Wrench (Figure 25). Now slide th
CONTACT US AT www.DRpower.com 23 9. Slide the Rod back through the Access Hole and reinstall the Hammers and Spacers in the same order as re
24 DR® CHIPPER/SHREDDER Chapter 5: Troubleshooting Most problems are easy to fix. Consult the Troubleshooting Table below for common problems
CONTACT US AT www.DRpower.com 25 Troubleshooting Table (Continued) SYMPTOM POSSIBLE CAUSE The Engine runs but the Flywheel doesn’t rotate.
26 DR® CHIPPER/SHREDDER Chapter 6: Parts Lists and Schematic Diagrams Parts List – DR CHIPPER/SHREDDER ASSEMBLY – CHIPPER SIDE and DRIVE SIDE
CONTACT US AT www.DRpower.com 27 Schematic – DR CHIPPER/SHREDDER ASSEMBLY – CHIPPER SIDE 110401
28 DR® CHIPPER/SHREDDER Schematic – DR CHIPPER/SHREDDER ASSEMBLY – DRIVE SIDE 110403
CONTACT US AT www.DRpower.com 29 Parts List and Schematic– DR CHIPPER/SHREDDER ROTOR ASSEMBLY NOTE: Part numbers listed are available through
CONTACT US AT www.DRpower.com 3 Read this Safety & Operating Instructions Manual before you use the DR CHIPPER/SHREDDER. Become familiar
30 DR® CHIPPER/SHREDDER Parts List – DR CHIPPER/SHREDDER BASIC ASSEMBLY NOTE: Part numbers listed are available through DR Power Equipment. Re
CONTACT US AT www.DRpower.com 31 Schematic – DR CHIPPER/SHREDDER BASIC ASSEMBLY 110404
75 MEIGS ROAD, P.O. BOX 25, VERGENNES, VERMONT 05491 ©2011 Country Home Products, Inc. All rights reserved 292221A Daily Checklist for the DR CHIPPE
4 DR® CHIPPER/SHREDDER This is a high-powered machine, with moving parts operating with high energy. You must operate the machine safely. Un
CONTACT US AT www.DRpower.com 5 Gasoline is a highly flammable liquid. Gasoline also gives off flammable vapor that can be easily ignited an
6 DR® CHIPPER/SHREDDER General Safety Operating this CHIPPER/SHREDDER safely is necessary to prevent or minimize the risk of death or serious
CONTACT US AT www.DRpower.com 7 A Note to All Users Under California law, and the laws of some other states, you are not permitted to operat
8 DR® CHIPPER/SHREDDER Figure 1 Chapter 2: Setting Up The DR CHIPPER/SHREDDER It may be helpful to familiarize yourself with the controls and
CONTACT US AT www.DRpower.com 9 Figure 2 12 11 6 7 8 5 10 9 Specifications Unpacking the DR CHIPPER/SHREDDER Tools and supplies ne
Commentaires sur ces manuels